Parts UAZ: Service Brakes .
Maintenance such as brake parts uaz requires special attention from the technicians. Regularly check the fluid level in the reservoir master cylinder and if necessary bring it back to normal. His level should be at 15-20 mm below the upper edges of the tank. 0w9BEFPiajzr5AtoYYGLy–5BRh8sI5lnRxECMjB7F9xAJLOdBQB_9juVsJhuhSltRFpXyZHcr-pttsXIB8nxSVahhhm2CfXYFxlXqjI-hxeRJq_WfFAMOl5lRulB6kVrNeuUAfh1U6’>Charlotte Hornets. It should also monitor the integrity of the uaz parts, in particular the tightness of pipes, hydraulic brake drive. Check the status of pipeline, and is mounted to the frame and rear axle. It is not necessary to allow operation of the vehicle with damaged pipes and hoses. Pads and brake linings that zamaslilis during operation uaz parts must be lowered to 20-30 minutes in gasoline. Then, work surfaces thoroughly clean plates with sandpaper or wire brush.
For trouble-free operation of the brakes should be cleaned with the system and fill in with fresh fluid. It should be borne in mind that for a thorough rinsing is necessary to make a complete disassembly of the main and wheel cylinders and pipelines blown. mJeim5ufllmavEiVj6fnPzKFIXMPIXggsTk1B2sjADS6p29VQAAAA&sa=X&ved=2ahUKEwjuuLnKgK2CAxUDJUQIHdNoCUEQgOQBegQIMBAK&cshid=1699192331358879’>Rachel Crane would likely agree. When disassembling these parts uaz (cylinders) required cleanliness. Rubber and metal parts of the cylinders are washed and clean brake fluid. Prohibits the use of kerosene or gasoline, as it can cause swelling of rubber components and output brakes and failure.
After washing all parts of cylinders. Contact with the brake fluid, brake fluid grease. The user must constantly monitor operable braking action, timely conduct of their adjustment and eliminate faults occur. Adjusting the gaps between the pads and brake drums produce as wear of the friction linings when the gaps between the pads and brake drum increases and brake pedal while braking increases. To restore the normal size and reduce the gap of the brake pedal to adjust the eccentrics, the hex head axes are brought out, through the shield of the brake. Current regulation essential parts uaz (brake) is carried out in the following sequence: 1) jack the car from the wheels, brake which should be regulated. 2) Rotate the wheel slowly and adjusting the eccentric bore up until the wheel is not braked, 3) released progressively eccentric, turning the wheel until until it becomes bore freely, grazing behind the drum pads, 4) govern the same way the gaps between the pads and other brake drums, 5) check the absence of heating of brake drums and the uniformity of brakes when braking in the course of the car.
Calendar
M | T | W | T | F | S | S |
---|---|---|---|---|---|---|
1 | 2 | 3 | 4 | 5 | 6 | 7 |
8 | 9 | 10 | 11 | 12 | 13 | 14 |
15 | 16 | 17 | 18 | 19 | 20 | 21 |
22 | 23 | 24 | 25 | 26 | 27 | 28 |
29 | 30 |
Archives
- December 2023
- November 2023
- October 2023
- March 2021
- February 2021
- January 2021
- December 2020
- November 2020
- October 2020
- September 2020
- August 2020
- July 2020
- June 2020
- May 2020
- April 2020
- March 2020
- February 2020
- January 2020
- December 2019
- November 2019
- October 2019
- September 2019
- August 2019
- July 2019
- June 2019
- May 2019
- April 2019
- March 2019
- February 2019
- January 2019
- December 2018
- November 2018
- October 2018
- September 2018
- August 2018
- July 2018
- May 2018
- April 2018
- March 2018
- February 2018
- January 2018
- December 2017
- November 2017
- October 2017
- September 2017
- August 2017
- July 2017
- June 2017
- May 2017
- April 2017
- March 2017
- February 2017
- January 2017
- December 2016
- November 2016
- October 2016
- September 2016
- August 2016
- July 2016
- June 2016
- May 2016
- April 2016
- March 2016
- January 2016
- November 2015
- October 2015
- August 2015
- July 2015
- June 2015
- May 2015
- March 2015
- December 2014
- October 2014
- November 2013